--- doc/build/Attic/install.html 2000/10/27 02:25:43 1.4 +++ doc/build/Attic/install.html 2000/11/21 15:45:00 1.8 @@ -9,7 +9,7 @@ Scott Harrison

-Last updated: 10/26/2000 +Last updated: 11/21/2000

This is the current list of steps to support LON-CAPA installation. These steps have @@ -24,7 +24,40 @@ RedHat 6.2 CD source tree. You need bootnet-20000407.img. (Download the image file; insert a blank floppy disk; and type a command similar to: dd if=bootnet-20000407.img of=/dev/fd0). For installation, you -need to specify http://www.lon-capa.org as your download URL, and /install/3.1/currentcdsource +need to specify hobbes.lite.msu.edu/~loninst as your download URL, and /3.1/currentcdsource +as the source location. + +

  • Install RedHat 6.2 + +
  • After installation, restart the computer. Login as root. Enter these two commands: +
      +
    1. lynx -source http://install.lon-capa.org/3.1/scripts/postinstall.pl>postinstall.pl +
    2. perl postinstall.pl +
    +
  • As postinstall.pl runs, you will be asked various questions. Follow the instructions to correctly +enter in the appropriate parameter values. + +
    +

    Old steps; do not use these...

    +Last updated: 11/01/2000 +

    +

    +This is the current list of steps to support LON-CAPA installation. These steps have +been tested. +

      +
    1. Get Redhat 6.2 on a CD by +
        +
      • Using a RedHat 6.2 CD +
      • Downloading a RedHat 6.2 CD image and burning a CD +
      • Or, alternatively do a network install from a +RedHat 6.2 CD source tree. You need to burn a boot floppy disk with a network boot image; + +bootnet-20000407.img. (Download the image file; insert a blank floppy disk; and type a +command similar to: dd if=bootnet-20000407.img of=/dev/fd0). For installation, you +need to specify hobbes.lite.msu.edu/~loninst as your download URL, and /3.1/currentcdsource as the source location.
    2. Install RedHat 6.2 @@ -53,9 +86,38 @@ http://install.lon-capa.org/3.1/FinalRPM altering configuration files present throughout the system. For a list of these files and their descriptions, visit http://install.lon-capa.org/3.1/loncapafiles/loncapafiles.html. +
    3. Important files are /etc/httpd/conf/access.conf, /etc/ntp.conf, /etc/krb.conf, /home/httpd/lonTabs/spare.tab, /home/httpd/lonTabs/hosts.tab (if setting up a cluster different than MSU's). +
    4. Unshadow passwords +
        +
        You can do this by these 5 steps:
+1. enter the system command, as "root", pwunconv
+2. enter the system command, as "root", grpunconv
+3. Set the following to be the /etc/pam.d/login file on your system
+#%PAM-1.0
+auth       required     /lib/security/pam_securetty.so
+auth       required     /lib/security/pam_pwdb.so shadow nullok
+auth       required     /lib/security/pam_nologin.so
+account    required     /lib/security/pam_pwdb.so
+password   required     /lib/security/pam_cracklib.so
+password   required     /lib/security/pam_pwdb.so nullok use_authtok
+session    required     /lib/security/pam_pwdb.so
+session    optional     /lib/security/pam_console.so
+4. Set the following to be the /etc/pam.d/passwd file on your system
+#%PAM-1.0
+auth       required     /lib/security/pam_pwdb.so shadow nullok
+account    required     /lib/security/pam_pwdb.so
+password   required     /lib/security/pam_cracklib.so retry=3
+password   required     /lib/security/pam_pwdb.so use_authtok nullok
+5. Set/reset passwords.  As "root" use 'passwd', and 'passwd www'
+to change the important passwords.  This creates crypt-processible
+passwords in /etc/passwd.
+
        +
      +
    5. Run, as root, ln -s /etc/mime.types /etc/httpd/conf/mime.types +
    6. Run, as root, /etc/rc.d/init.d/httpd start.
    7. Run, as root, /etc/rc.d/init.d/loncontrol start.
    8. After 10 minutes, you should be able to check the file /home/httpd/html/lon-status/index.html to see if your machine has been successfully set up.